Wyoming licensing exam

Wyoming Limited Water Well and Irrigation Technician Exam: Practice Test & Licensing Guide

Wyoming's limited water well and irrigation technician exam (ICC 474): 40 questions on branch circuits, wiring methods, grounding and bonding, and equipment and motors for water wells and irrigation systems. Open book, 70% to pass.

Questions
40
Time limit
2 hours
Passing score
70%

Full practice test: $19One-time payment · 12 months of access

Try 10 free practice questions

No sign-up. Every answer explains the rule and tells you where to find it in your book.

Question 1 of 10General Knowledge, Theory, Basic Load Calculations, and Definitions

A 240-volt resistive heat-trace cable on a wellhead riser pipe has a measured resistance of 19.2 ohms. What current does it draw when energized?

Requirements at a glance

AgencyWyoming Department of Fire Prevention and Electrical Safety (State Fire Marshal); exam by ICC through Pearson VUE
Exam40 questions, 2 hours, 70% to pass
Experience4,000 hours over at least 2 years.
Books allowedNEC or NEC Handbook (2023 per ICC's August 2025 bulletin), Ugly's (any edition), Ferm's Fast Finder, Tom Henry's Key Word Index
Fees$115 per exam to Pearson VUE; the license is $100 for 3 years.

Technicians applying to the Wyoming State Fire Marshal for a limited water well and irrigation technician license. You need 4,000 hours of experience over at least 2 years.

How to get licensed, step by step

  1. Check your experience

    Make sure you meet the State Fire Marshal's requirements for the limited water well and irrigation technician license: 4,000 hours over at least 2 years.

    Wyoming State Fire Marshal: electrical licensing (opens in a new tab)

  2. Apply and get approved

    Apply through the Wyoming electrical licensing portal. Wait for your approval notice, then allow 24 to 48 hours before you schedule so ICC can process your record.

    Apply and pay for your license (Wyoming electrical licensing portal) (opens in a new tab)ICC Wyoming Electrical Contractor/Trades Bulletin (PDF) (opens in a new tab)

  3. Register and pay with Pearson VUE

    Create a Pearson VUE account for ICC, pick the Wyoming exam, pay $115 and book a seat at a test center.

    Register with ICC at Pearson VUE (opens in a new tab)

  4. Pass the exam

    Bring your tabbed references. Your result shows right after the exam. If you fail, you must wait 10 days before you retest, and each attempt costs a new fee.

    Register with ICC at Pearson VUE (opens in a new tab)041-5 Wyo. Code R. § 3 (examinations and passing scores) (opens in a new tab)

How to prepare

  • ICC's August 2025 bulletin still lists the 2023 NEC, but Wyoming has adopted the 2026 NEC. Check ICC's exam catalog for your exam before you buy a book.
  • Tab your books before exam day. There's no time to look up every answer, so know where Articles 90, 100, 110, 210 to 250, 300 to 392, 430 and Chapter 9 sit.
  • Equipment and motors are 11 of the 40 questions: know Article 430 motor circuits and the pump and irrigation equipment rules in your NEC.
  • General knowledge and branch circuits with overcurrent protection are 8 questions each. Grounding and bonding is 6.
  • Start with the free questions above to find your weak topics, then drill those first.
  • Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
  • Read every explanation, including for questions you got right, and look the section up in your own book.

Books for this exam

This is an open-book exam: you can bring the references below, and most questions come from the NEC. Tabs and highlighting are allowed. Free online copies are read-only and can't be used in the exam room.

  • NFPA 70: National Electrical Code (NEC), 2023 Edition (or the NEC Handbook)Essential

    Bring your own; the exam is based on the code provisions only. ICC's August 2025 bulletin lists the 2023 edition even though Wyoming adopted the 2026 NEC, so check ICC's exam catalog before you buy.

    NFPA store (opens in a new tab)Free online access (opens in a new tab)

  • Ugly's Electrical References (any edition)

    Allowed in the exam room. Formulas for Ohm's law, voltage drop, motors and transformers.

    Jones & Bartlett (opens in a new tab)

  • Ferm's Fast Finder Index or Tom Henry's Key Word Index

    Both are allowed, and a good index saves time on the questions you must look up.

Official reference list (as published by the testing agency)
  • NFPA 70: National Electrical Code (NEC) or NEC Handbook (code provisions only are tested), 2023 Edition per ICC's August 2025 bulletin
  • Ugly's Electrical References (any edition)
  • Optional: Ferm's Fast Finder Index or Tom Henry's Key Word Index

What's on the exam

Official content outline from the International Code Council (ICC), delivered by Pearson VUE, (number of questions per topic):

TopicQuestions
General Knowledge, Theory, Basic Load Calculations, and Definitions8
Branch Circuits, Overcurrent Protection, and Conductors (Load Side of Disconnect to Equipment)8
Wiring Methods and Conductors (Load Side of Disconnect to Equipment)7
Grounding and Bonding6
Equipment and Motors (Load Side of Disconnect to Equipment)11

Exam day details

  • Administered by the International Code Council (ICC), delivered by Pearson VUE, for the Wyoming Department of Fire Prevention and Electrical Safety (State Fire Marshal).
  • Fee: $115 per exam, paid to Pearson VUE when you schedule. State license fees are separate.
  • 40 questions in 2 hours; 70% to pass (041-5 Wyo. Code R. § 3).
  • Open book. ICC's August 2025 bulletin lists the 2023 NEC as the reference, even though Wyoming has adopted the 2026 NEC for enforcement. Check ICC's exam catalog for your exam before you buy a book.
  • Apply to the State Fire Marshal and get approved first, then register with ICC through Pearson VUE. ICC suggests waiting 24 to 48 hours after approval before you schedule.
  • Questions are four-option multiple choice and there is no penalty for guessing. Your result shows right after the exam.
  • You must wait 10 days before retaking a failed exam. Each attempt needs a new fee.
  • ICC exam number 474. "Equipment and Motors (Load Side of Disconnect to Equipment)" is 11 of the 40 questions, so weight your study there.

Frequently asked questions

What's on the Wyoming limited water well and irrigation technician exam?

ICC's August 2025 outline, 40 questions: General Knowledge, Theory, Basic Load Calculations, and Definitions 8; Branch Circuits, Overcurrent Protection, and Conductors (Load Side of Disconnect to Equipment) 8; Wiring Methods and Conductors (Load Side of Disconnect to Equipment) 7; Grounding and Bonding 6; Equipment and Motors (Load Side of Disconnect to Equipment) 11.

Which NEC edition do I bring to the Wyoming electrical exam?

ICC's August 2025 bulletin lists the 2023 NEC, although Wyoming has adopted the 2026 NEC for enforcement. The NEC Handbook, Ugly's (any edition), Ferm's Fast Finder and Tom Henry's Key Word Index are also allowed. Check ICC's exam catalog before you buy a book.

Who gives the Wyoming electrical exams?

ICC, through Pearson VUE. The State Fire Marshal approves your application first; then you register and pay Pearson VUE $115 and test at a Pearson VUE center.

Free questions with answers

Show all 10 free questions and answers
  1. A 240-volt resistive heat-trace cable on a wellhead riser pipe has a measured resistance of 19.2 ohms. What current does it draw when energized?

    Answer: 12.5 A

    Ohm's law: I = E / R = 240 / 19.2 = 12.5 A. The 0.08 A figure comes from dividing resistance by voltage (R / E), 220.8 A subtracts resistance from voltage, and 4,608 A multiplies the two.

    Reference: General electrical theory, Ohm's law: I = E / R

  2. A single-phase, 240-volt resistive tank heater in a pump house draws 18 amperes. How many watts does it consume?

    Answer: 4,320 W

    For a resistive single-phase load, P = E x I = 240 x 18 = 4,320 W. The 7,482 W figure wrongly applies the 1.732 three-phase factor, 13.3 results from dividing voltage by current, and 258 adds the two numbers.

    Reference: General electrical theory, Power formula: P = E x I

  3. As defined in Article 100, a continuous load is one where the maximum current is expected to continue for how long?

    Answer: 3 hours or more

    Article 100 defines a continuous load as a load where the maximum current is expected to continue for 3 hours or more. This definition drives the 125 percent sizing rules for branch circuits and feeders.

    Reference: NFPA 70, National Electrical Code, 2023, Article 100, Definitions: Load, Continuous

  4. A 10-hp, 230-volt, three-phase pump motor supplies a deep-well pump and has its own branch circuit. Using Table 430.250 and 75 C terminations, what is the smallest copper conductor permitted?

    Answer: 10 AWG

    Table 430.250 lists 28 A for a 10-hp, 230-volt, three-phase motor. Branch-circuit conductors must be at least 125 percent of that, 28 x 1.25 = 35 A (430.22). The 75 C column of Table 310.16 gives 35 A for 10 AWG; 12 AWG (25 A) is too small and 8 AWG (50 A) is larger than needed.

    Reference: NFPA 70, National Electrical Code, 2023, 430.22; Table 430.250; Table 310.16

  5. A 3-hp, 230-volt, single-phase motor drives a booster pump on its own branch circuit. Using Table 430.248 and 75 C terminations, what is the smallest copper conductor permitted?

    Answer: 12 AWG

    Table 430.248 lists 17 A for a 3-hp, 230-volt, single-phase motor. The conductors must carry at least 17 x 1.25 = 21.25 A (430.22). In the 75 C column of Table 310.16, 14 AWG is only 20 A, so 12 AWG (25 A) is the smallest that works.

    Reference: NFPA 70, National Electrical Code, 2023, 430.22; Table 430.248; Table 310.16

  6. Three-conductor, 10 AWG Type UF-B copper cable supplies a pump with 90 C-rated insulation. Which Table 310.16 temperature column sets its ampacity?

    Answer: 60 C

    Section 340.80 limits the ampacity of Type UF cable to that of 60 C conductors, regardless of the insulation temperature marking. For 10 AWG copper that is 30 A.

    Reference: NFPA 70, National Electrical Code, 2023, 340.80

  7. What is the maximum number of 10 AWG THWN copper conductors (0.0211 sq. in. each) permitted in a 3/4 in. EMT (total area 0.533 sq. in.) with more than two conductors?

    Answer: 10

    Chapter 9 Table 1 limits fill to 40 percent when there are more than two conductors: 0.533 x 0.40 = 0.213 sq. in. Dividing, 0.213 / 0.0211 = 10.09, so 10 conductors fit. Counting against 53 percent (0.283 sq. in.) would wrongly permit 13.

    Reference: NFPA 70, National Electrical Code, 2023, Chapter 9, Table 1; Table 4; Table 5

  8. A 5-hp, 230-volt single-phase pump motor branch circuit uses a 45 A inverse-time breaker. Using Table 250.122, what is the smallest copper equipment grounding conductor?

    Answer: 10 AWG

    The equipment grounding conductor is sized from the rating of the overcurrent device. 45 A is above the 40 A row, so the next row, 60 A, applies in Table 250.122, which lists 10 AWG copper. 12 AWG is the value for 20 A, and 8 AWG is for 100 A.

    Reference: NFPA 70, National Electrical Code, 2023, 250.122(A); Table 250.122

  9. A 15-hp, 460-volt, three-phase pump motor (table full-load current 21 A) has its own disconnect. What is the minimum ampere rating of the motor-circuit switch under 430.110(A)?

    Answer: 24.15 A

    The disconnecting means must have an ampere rating of at least 115 percent of the motor's full-load current: 21 x 1.15 = 24.15 A. 26.25 A is the 125 percent conductor factor, and 36.75 A is the 175 percent fuse factor.

    Reference: NFPA 70, National Electrical Code, 2023, 430.110(A)

  10. What must a disconnecting means for a three-phase pump motor do, according to 430.103?

    Answer: Open all ungrounded conductors together; no pole operable alone

    430.103 requires the motor disconnect to disconnect the motor and controller from all ungrounded supply conductors and to be designed so that no pole can be operated independently. The grounded conductor is not switched.

    Reference: NFPA 70, National Electrical Code, 2023, 430.103

Sources

Questions last verified October 29, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.