Requirements at a glance
| Exam | Water Distribution Class I: 100 scored questions, closed book, formula sheet provided |
|---|---|
| Colorado equivalent | Distribution Class 1 |
| Passing score | Set by your state; 70 in Colorado and most WPI states |
| Colorado fees | $50 CDPHE application + $104 PSI exam |
Entry-level distribution system operators in states that use WPI exams, including Colorado Distribution Class 1 (the most-taken drinking water exam in Colorado) and Idaho Drinking Water Distribution Class I.
Official links
How to get certified, step by step
Meet your state's eligibility rules
Most states need a high school diploma or GED and some experience. In Colorado: the free regulatory course for your certificate type, plus one month of supervised experience for Class D or 1.
CDPHE: which certificate is right for you (opens in a new tab)
Apply to your certifying agency
Apply to your state program (in Colorado, CDPHE's Certified Water Professionals program). Once approved, you get instructions to schedule with PSI.
CDPHE: steps to becoming certified (Colorado) (opens in a new tab)
Take the exam
At a PSI test center or by remote proctoring. WPI's formula/conversion sheet is provided; bring a basic calculator.
Get certified
Your state issues the certificate after you pass. Higher classes need more experience and the next exam level.
How to prepare
- Learn the formula sheet before exam day: know which formula each problem needs and practice unit conversions (gallons, cubic feet, pounds, psi, feet of head).
- System components (pipe, valves, hydrants, meters, storage) are 35 questions: know materials, valve types and flushing.
- Practice cross-connection and backflow basics, disinfection of new mains, and chlorine residual rules.
- Start with the free questions above to find your weak topics, then drill those first.
- Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
- Read every explanation, including for questions you got right, and look the section up in your own book.
What to study
This is a closed-book exam, so nothing comes into the exam room. Study from these:
WPI formula/conversion sheetEssential
Provided at the exam. Practice with it so you know where each formula is.
WPI: exam references and formula sheets (opens in a new tab)
40 CFR Part 141: National Primary Drinking Water Regulations
Source of MCLs, monitoring and public notification rules.
40 CFR Part 141 (drinking water rules), eCFR (opens in a new tab)
OSHA 29 CFR 1910.146 (confined spaces) and 1926 Subpart P (excavations)
The safety questions.
Sacramento State (Office of Water Programs) operator training manuals
WPI's main references for operation questions. Not allowed in the exam room.
Official reference list (as published by the testing agency)
- WPI formula/conversion sheet (provided at the exam)
- 40 CFR Parts 141 and 143 (Safe Drinking Water Act rules) and 40 CFR Part 503 (biosolids)
- 29 CFR 1910 and 1926 (OSHA safety)
What's on the exam
Official content outline from Water Professionals International (WPI, formerly ABC); delivered by PSI (number of questions per topic):
| Topic | Questions | |
|---|---|---|
| Distribution System Components | 35 | |
| Equipment Installation, Operation, Maintenance and Repair | 30 | |
| Water Quality Monitoring and Laboratory Analysis | 15 | |
| Security, Safety, Administration and Public Interactions | 20 |
Exam day details
- Administered by Water Professionals International (WPI, formerly ABC); delivered by PSI for most states.
- Fee: Set by your state. In Colorado: $104 to PSI plus a $50 CDPHE application fee.
- 100 scored questions, about 9 of them calculations.
- Up to 10 extra unscored pretest questions are mixed in.
- Passing is set by your state; Colorado and most WPI states use 70. WPI's 2025 exams are reported as scaled scores.
- WPI's formula/conversion sheet is provided; bring a basic non-programmable calculator.
- Time is set by the state and PSI (typically 3 hours for a 100-question exam); PSI confirms it when you schedule.
- Colorado: Class D/1 = WPI Class I up to Class A/4 = Class IV. You need a high school diploma or GED and Colorado's free regulatory course.
Frequently asked questions
Which Colorado certificate uses the Distribution Class I exam?
Colorado Distribution Class 1. Colorado's classes map to WPI's: Class 1 is Class I, up to Class 4 = Class IV. You also need the free regulatory course and one month of supervised experience.
How hard is the Water Distribution Class I exam?
In Colorado's 2024 report, 68% of first-time takers passed, but repeat takers passed only about a third of the time.
Does Idaho use this exam?
Idaho operators are licensed by DOPL's Board of Drinking Water and Wastewater Professionals in Classes I to IV, and Idaho's operator exams are ABC (now WPI) exams. Idaho's Class I matches WPI Class I. Check with DOPL for the current application and exam steps.
Free questions with answers
Show all 10 free questions and answers
A standpipe is 20 ft (6.1 m) in diameter and holds water 40 ft (12.2 m) deep. About how many gallons does it hold?
Answer: 93,950 gal
Volume of a cylinder = 0.785 × D² × height = 0.785 × 20 ft × 20 ft × 40 ft = 12,560 ft³. Convert with 7.48 gal/ft³: 12,560 × 7.48 = 93,949 gal, about 93,950 gal. 12,560 is the answer left in cubic feet. 23,490 comes from using the 10 ft radius in place of the diameter. 375,800 comes from using 3.14 × D² (the radius formula with a diameter).
Reference: WPI Formula/Conversion Table, Water Treatment, Distribution & Laboratory (2024), Volume of Cylinder; 1 cubic foot of water = 7.48 gal
A plating shop with toxic chemicals needs a backflow assembly at its water service. The device must handle both backpressure and back-siphonage at a high hazard. Which one fits?
Answer: A reduced pressure zone (RPZ) assembly
Only an air gap, a barometric loop or a reduced pressure zone (RPZ) assembly is accepted for high-hazard connections. The RPZ has two check valves with a relief valve between them that dumps water to the air if backflow starts, so it covers both backpressure and back-siphonage. A double check covers both types of backflow but is only for low hazards. Pressure and hose bibb vacuum breakers protect against back-siphonage only.
Reference: Kentucky DEP Distribution System Operator Certification Manual (2013), Chapter 13: Cross-Connection Control, Degree of Hazard and Reduced Pressure Zone
A routine distribution sample is total coliform-positive. Under the Revised Total Coliform Rule, what repeat sampling is required?
Answer: At least 3 repeat samples within 24 hours: the original tap and taps within 5 connections upstream and downstream
Under 40 CFR 141.858(a), the system must collect at least three repeat samples within 24 hours of learning of the positive result, all on the same day. Per the sample siting plan in 141.853(a)(5), they come from the original tap, a tap within five service connections upstream and a tap within five service connections downstream. A single repeat, or a 72-hour window, would not meet the rule, and repeats are required for any total coliform-positive sample, not only E. coli-positive ones.
Reference: 40 CFR 141 Subpart Y (Revised Total Coliform Rule), 40 CFR 141.858(a)(1) and 141.853(a)(5)
A main break has been repaired and the section is ready to be refilled. How should the crew refill it?
Answer: Crack a valve at the low end slowly while venting air at a hydrant, service or air valve
Refill slowly from the low end, opening the fill valve just a crack, while air escapes from a hydrant, service or air relief valve at the high point. Keep the velocity low (below about 1 ft/sec) and control it with the fill valve, not the vent. Filling fast traps air and can cause water hammer when the pipe suddenly becomes full. After refilling, check the repair for leaks, then disinfect and take bacteriological samples.
Reference: New Mexico Water Systems Operator Certification Study Manual, Chapter 7: Distribution, Repairing the Leak (step 7)
A crew flushes an 8-inch main through a hydrant at about 1 ft/sec. The water clears quickly, but rusty-water complaints return within days. What is the most likely cause?
Answer: The velocity was too low to scour sediment and biofilm from the pipe
Flushing only cleans the pipe if the water moves fast enough to scour it. A minimum of about 2.5 ft/sec is needed, and 5 to 6 ft/sec is best for removing sediment and biofilm. At 1 ft/sec the crew mostly replaced the stale water, so the deposits stayed and soon caused complaints again. Unidirectional flushing (closing valves so water moves one way at higher speed) helps reach these velocities. Opening a hydrant slowly is correct practice.
Reference: Kentucky DEP Distribution System Operator Certification Manual (2013), Chapter 6: Pipes & Services, Flushing and Cleaning
Which type of meter is most commonly used on single-family homes?
Answer: Positive displacement meter (nutating disc or piston)
Positive displacement meters, such as nutating disc and oscillating piston meters, are the most common meters in water systems. They are used for homes and small commercial services up to about 2 inches. Each time the measuring chamber fills and empties, a known volume passes, so they are accurate at the low flows typical of a house. Propeller and venturi meters are for large lines, and compound meters are for services with widely varying flows.
Reference: New Mexico Water Systems Operator Certification Study Manual, Chapter 7: Distribution, Positive Displacement Meters
A centrifugal pump with packing (not a mechanical seal) is running. What should the operator see at the stuffing box?
Answer: A slow drip of water that cools and lubricates the packing
Packing rubs on the turning shaft sleeve and makes heat, so some water has to leak through to cool and lubricate it. A rule of thumb is roughly 20 to 60 drops per minute, depending on pump size and packing. If the gland is tightened until leakage stops, the packing overheats and scores the shaft sleeve. If the leak-off water feels warm, there isn't enough flow. A steady stream means the packing needs adjustment or replacement.
Reference: New Mexico Water Systems Operator Certification Study Manual, Chapter 10: Mechanical Systems, Pump Packing (Repacking the Pump)
A variable frequency drive slows a pump to 90% of full speed. Using the affinity laws, about how much do flow, head and power change?
Answer: Flow 90%, head 81%, power 73% of the original
The affinity laws say flow changes in direct proportion to speed, head with the square of speed, and power with the cube. At 90% speed: flow = 0.90, head = 0.90² = 0.81, power = 0.90³ = 0.73. That cube relationship is why a VFD saves so much energy compared with throttling a valve at full speed. The other choices mix up which quantity goes with which exponent.
Reference: Kentucky DEP Distribution System Operator Certification Manual (2013), Chapter 11: Centrifugal Pumps, Affinity Laws
Before entering a permit-required confined space, in what order must the atmosphere be tested?
Answer: Oxygen, then flammable gases and vapors, then toxic gases
OSHA requires testing with a calibrated direct-reading instrument for oxygen first, then flammable gases and vapors, then toxic contaminants (29 CFR 1910.146(c)(5)(ii)(C) and (d)(5)(iii)). Oxygen goes first because many combustible gas sensors need enough oxygen to read correctly, and low oxygen is itself immediately dangerous. Flammable gases come before toxics because an explosion threatens everyone at once.
Reference: 29 CFR 1910.146 (Permit-Required Confined Spaces), 29 CFR 1910.146(d)(5)(iii)
A gas meter lowered into a meter vault reads 18.9% oxygen. What should the crew conclude?
Answer: The vault is oxygen-deficient and hazardous to enter
OSHA treats oxygen below 19.5% or above 23.5% as a hazardous atmosphere (29 CFR 1910.146(b)). Normal air is about 20.9% oxygen. A reading of 18.9% means something has used up or pushed out oxygen, so the vault must be ventilated and retested before anyone enters. A zero flammable reading doesn't make up for low oxygen. Above 23.5% would be oxygen-enriched, a fire hazard.
Reference: 29 CFR 1910.146 (Permit-Required Confined Spaces), 29 CFR 1910.146(b), definition of hazardous atmosphere
Sources
- WPI: Water Distribution Class I Need-to-Know Criteria (2025) (opens in a new tab)
- CDPHE: Steps to becoming a certified water professional (opens in a new tab)
- WPI: exam references and formula sheets (opens in a new tab)
- Idaho DOPL: Board of Drinking Water and Wastewater Professionals (opens in a new tab)
Questions last verified October 21, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.