Requirements at a glance
| Agency | Minnesota Department of Labor and Industry (DLI); Plumbing Board sets the rules |
|---|---|
| Experience | Completed apprenticeship, or 4 years and 7,000 hours as a registered unlicensed plumber |
| Exam | 240 points, 5.5 hours, 70% to pass |
| Books allowed | None of your own: DLI supplies the 2020 Minnesota Plumbing Code (without tabs), the laws-and-rules booklet and a calculator |
| Fees | $50 per personal-license exam (Minn. Stat. 326B.092), plus application and license fees |
Plumbers applying to DLI for a journeyworker license after an apprenticeship or 4 years and 7,000 hours as a registered unlicensed plumber.
Official links
How to get licensed, step by step
Apply to DLI
Send DLI your journeyworker plumber application, proof of apprenticeship or experience and the $50 exam fee. Licenses expire December 31 of odd years with 16 hours of continuing education (8 on code).
Minnesota Department of Labor and Industry (DLI) (opens in a new tab)DLI: plumbing license basics (opens in a new tab)
Schedule your exam
After DLI approves your application, you schedule the exam in DLI's iMS system. DLI gives exams at its St. Paul office (Tuesday to Thursday) and at outstate sites including Duluth, Mankato, Rochester and St. Cloud.
Take the exam
You have 5.5 hours and need 70%. The exam is open book with DLI-supplied references; no personal books, notes or electronic devices.
DLI: plumbing license basics (opens in a new tab)DLI Plumbing License Examination Guide (PDF) (opens in a new tab)
Results and retakes
DLI mails results in about 2 weeks. If you fail, wait 30 days after receiving results before reapplying.
How to prepare
- The exam uses the 2020 Minnesota Plumbing Code (Rules 4714): the 2018 UPC with Minnesota amendments. DLI scores the journeyworker exam out of 240 points and the master exam out of 300 points; each question is worth the same unless stated otherwise.
- DLI's guide lists knowledge areas by code chapter, including pipe sizing from the Chapter 6, 7, 9 and 11 tables with sample drawings. Learn fixture-unit values, trap and vent sizes and the Minnesota amendments.
- Every DLI exam is open book, but with DLI-supplied references only: a code book without tabs, the DLI laws-and-rules booklet and a desk calculator. You cannot bring your own books, so practice finding answers fast rather than relying on tabs.
- DLI publishes no topic weights, so our topic split is an estimate. Several versions of each exam are in use, and some questions ask for more than one answer or the choice that does not apply.
- Read DLI's Plumbing License Examination Guide: it marks each code chapter and topic as appearing on the master, journeyworker or other exams.
- Start with the free questions above to find your weak topics, then drill those first.
- Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
- Read every explanation, including for questions you got right, and look the section up in your own book.
Books for this exam
This is an open-book exam: you can bring the references below, and most questions come from the Minnesota Plumbing Code. Tabs and highlighting are allowed. Free online copies are read-only and can't be used in the exam room.
2020 Minnesota Plumbing Code (Minnesota Rules chapter 4714)Essential
DLI supplies the code book (without tabs) in the exam room. It is the 2018 Uniform Plumbing Code with Minnesota amendments.
DLI Plumbing License Examination Guide (April 2022)
DLI's own list of the code chapters and knowledge areas on each plumbing exam, with sample questions and formulas.
Official reference list (as published by the testing agency)
- 2020 Minnesota Plumbing Code, Minnesota Rules chapter 4714 (the 2018 Uniform Plumbing Code with Minnesota amendments). DLI provides the code book, without tabs.
- Minnesota Rules chapter 4716 (plumber licensing) and Minnesota Statutes 144, 325 and 326B (in the DLI laws-and-rules booklet)
What's on the exam
Estimated topic weighting. No official breakdown is published:
| Topic | Questions | |
|---|---|---|
| Chapter 2: Definitions | 4 | |
| Chapter 3: General Regulations | 8 | |
| Chapter 4: Plumbing Fixtures and Fixture Fittings | 8 | |
| Chapter 5: Water Heaters | 5 | |
| Chapter 6: Water Supply and Distribution | 10 | |
| Chapter 7: Sanitary Drainage | 14 | |
| Chapter 8: Indirect Wastes | 3 | |
| Chapter 9: Vents | 12 | |
| Chapter 10: Traps and Interceptors | 5 | |
| Chapter 11: Storm Drainage | 6 | |
| Pipe Sizing: Water, Drain, Waste and Vent | 14 | |
| Minnesota Plumber Licensing and Law (Rules 4716, Statutes 326B) | 5 |
Exam day details
- Administered by the Minnesota Department of Labor and Industry (DLI), which gives its own exams.
- Fee: $50 per personal-license exam (Minn. Stat. 326B.092). Application and license fees are separate.
- 5.5 hours, open book with DLI-supplied references; 70% to pass. DLI scores the exam out of 240 points; our practice exam uses 100 questions.
- Open book with DLI-supplied references: you get the code book (without tabs), the DLI laws-and-rules booklet and a desk calculator. You cannot bring your own books, notes or electronic devices.
- DLI gives the exam at its St. Paul office and outstate sites, scheduled after DLI approves your application. The time limit is 5.5 hours; the passing score is 70%.
- Results are mailed in about 2 weeks. If you fail, wait 30 days after receiving results before reapplying.
- Some questions ask you to pick more than one answer (the question says how many) or the one choice that does not apply. Several versions of each exam are in use.
- DLI scores the journeyworker exam out of 240 points and the master exam out of 300 points, each question worth the same unless stated otherwise. DLI does not publish a question count, so our practice length is an estimate.
- DLI's guide lists code chapters as knowledge areas (not every area appears on every exam) and gives no weights, so our topic split is an estimate. Some calculation questions have no multiple-choice answers on the real exam.
- The exam uses the 2020 Minnesota Plumbing Code. The 2018 UPC is its base, but where Minnesota Rules 4714 amend it, our questions use the Minnesota text. A review of the 2024 UPC was under way in late 2025; no adoption had been found, so the exam stays on the 2020 code.
Note: DLI scores the plumbing exams in points (240 journeyworker, 300 master) and publishes no question count or topic weights, so our practice length and topic split are estimates. Table values come from the 2018 UPC and Minnesota Rules 4714; confirm sizing tables in the code book DLI provides.
Frequently asked questions
Which plumbing code is on the Minnesota exam?
The 2020 Minnesota Plumbing Code (Minnesota Rules chapter 4714), which is the 2018 Uniform Plumbing Code with Minnesota amendments.
How is the Minnesota journeyworker plumber exam scored?
Out of 240 points, each question worth the same unless stated otherwise, with no partial credit. You need 70%.
Do I need to know pipe sizing?
Yes. DLI's guide lists water, drain, waste and vent and storm sizing from the Chapter 6, 7, 9 and 11 tables, with sample drawings.
Free questions with answers
Show all 10 free questions and answers
Hubless cast-iron DWV pipe with shielded couplings runs horizontally in 10-foot lengths. Per Minnesota Table 313.3 and its notes, how must it be supported?
Answer: At every joint where lengths are over 4 feet, with hangers placed adjacent to the joint and never on the coupling
Table 313.3 lists hubless pipe as supported at every other joint, unless the length is over 4 feet, then at each joint. Note 1 puts the support adjacent to the joint (within 18 inches), and Note 4 says hangers shall not be placed on the coupling. The 5 foot/10 foot rule is for cast-iron pipe with lead and oakum joints.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), Minn. R. 4714.0313, Table 313.3 notes 1-4
What are the maximum water consumption figures for water closets and urinals under UPC Sections 411.2 and 412.1?
Answer: Water closets 1.6 gallons per flush; urinals an average of 1 gallon per flush
Section 411.2 limits water closets to 1.6 gallons per flush, and Section 412.1 limits urinals to an average of 1 gallon per flush. Minnesota's amendment to 412.1.1 only concerns nonwater urinals. This is also why Tables 610.3 and 702.1 list a 1.6 GPF water closet as the standard rated fixture.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), UPC 411.2; 412.1
UPC 504.6, as adopted in Minnesota, sets a minimum for the discharge capacity of a temperature and pressure relief device on a water heater. What is it?
Answer: Not less than the input rating of the water heater, in Btu per hour
Section 504.6 as amended by Minn. R. 4714.0504 requires the hourly Btu discharge capacity (or rated steam relief capacity) of the device to be not less than the input rating of the water heater. It also prohibits a shutoff valve between the relief valve and the heater or on the discharge pipe, and sends discharge piping to 608.5.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), Minn. R. 4714.0504, subp. 2 (UPC 504.6)
Under Minn. R. 4714.0609 (UPC 609.1), how deep must building supply and yard water piping be installed?
Answer: At least 12 inches below the maximum local frost depth, and not less than 12 inches below finish grade
The amended 609.1 locates building supply and yard piping not less than 12 inches below the maximum local frost depth (per 312.6) or an alternative approved by the authority, and the cover must be not less than 12 inches below finish grade. The frost depth itself comes from the local frost depth, and Minnesota's statewide values appear in Minn. R. 1303.1600, so this rule is added to whichever applies.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), Minn. R. 4714.0609, subp. 1 (UPC 609.1)
Under Minn. R. 4714.0707 (UPC 707.4), which condition in a horizontal drainage line requires an additional cleanout?
Answer: An aggregate horizontal change of direction exceeding 135 degrees
UPC 707.4 as amended requires a cleanout at the upper terminal of each horizontal drainage pipe, one for each 100 feet (or fraction) of developed length over 100 feet, and an additional cleanout for each aggregate horizontal change of direction exceeding 135 degrees. Two 45-degree bends or a 90 plus a 45 do not exceed 135 degrees, so the 90 degree threshold in the second choice is wrong.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), Minn. R. 4714.0707 (UPC 707.4)
An individual vent serves a fixture drain that is 4 inches in diameter. What is the minimum size of the individual vent under UPC 904.1?
Answer: 2 inches
Section 904.1 requires an individual vent to be not less than 1-1/4 inches in diameter and not less than one-half the diameter of the drain it connects to. Half of 4 inches is 2 inches, which governs because it is larger than 1-1/4 inches. The 1-1/2 inch choice is half of a 3 inch drain, not a 4 inch one, and the vent must also satisfy Table 703.2 for its load and length.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), UPC 904.1; Table 703.2 note 6
Using Table 1002.2, what is the maximum developed length of trap arm from the trap weir to the vent for a 2 inch trap arm?
Answer: 60 inches (5 feet)
Table 1002.2 lists maximum trap arm lengths: 30 inches for 1-1/4 inch, 42 inches for 1-1/2 inch, 60 inches for 2 inch, 72 inches for 3 inch, and 120 inches for 4 inch and larger. The minimum distance is two times the trap arm diameter (1002.2). The arm keeps 1/4 inch per foot slope, and a water closet is allowed 6 feet measured from the top of the closet flange.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), UPC 1002.2, Table 1002.2; Minn. R. 4714.1002
Unless the roof is certified for the maximum depth of ponding, where must the secondary (emergency) roof drain be located under Minn. R. 4714.1101?
Answer: 2 inches above the lowest point of the roof surface
Section 1101.12.2.1 as amended places secondary roof drainage 2 inches above the lowest point of the roof surface unless a registered design professional specializing in structural engineering certifies the roof for the maximum possible depth of ponding under chapter 1305. Engineered siphonic systems may not serve as secondary drainage.
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), Minn. R. 4714.1101, subp. 4 (UPC 1101.12.2.1)
What is the maximum design velocity for hot water in copper tube systems under UPC 610.12.1?
Answer: 5 feet per second
Section 610.12.1 limits velocity in copper and copper alloy tube systems to 8 ft/s for cold water and 5 ft/s for hot water. The same limits apply through copper fittings used on other tubing (610.12.2).
Reference: 2020 Minnesota Plumbing Code (Minn. R. ch. 4714, 2018 UPC), UPC 610.12.1
How much practical plumbing experience does Minn. R. 4716.0020 count as one year?
Answer: At least 1,750 hours
Rule 4716.0020, subpart 2 says one year of practical plumbing experience consists of at least 1,750 hours, and not more than 1,750 hours are credited for one calendar year. Four years therefore equals 7,000 hours.
Reference: Minnesota Rules, chapter 4716, Minn. R. 4716.0020, subp. 2 (A)-(B)
Sources
- DLI Plumbing License Examination Guide (April 2022) (opens in a new tab)
- Minnesota DLI: plumbing license basics (opens in a new tab)
- Minnesota DLI: license exam schedule (opens in a new tab)
Questions last verified November 9, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.