Arkansas licensing exam

Arkansas HVACR Class D Exam (Prov): Practice Test & Licensing Guide

The Prov exam for an Arkansas Class D HVACR license, the sheet metal (ductwork) license: 60 open-book questions in 3 hours, 70% to pass.

Questions
60
Time limit
3 hours
Passing score
70%

Full practice test: $19One-time payment · 12 months of access

Try 10 free practice questions

No sign-up. Every answer explains the rule and tells you where to find it in your book.

Question 1 of 10Fuel Gas Systems

A new section of consumer gas piping has a proposed maximum working pressure of 5 psig. Under Section 406.4.1 of the Arkansas Fuel Gas Code, what is the minimum pressure at which it must be tested?

Requirements at a glance

AgencyArkansas HVACR Licensing Board (Department of Labor and Licensing); exams by Prov
ExperienceApplicants with no license history need 2 years of experience as an HVACR contractor or employee of one, or Board-approved training (17 CAR 261; our copy is an August 2025 draft)
ExamClass D HVACR, sheet metal (60 questions, 3 hours, 70% to pass, open book)
Books allowedThe Arkansas HVAC/R Law and Rules, SMACNA HVAC Duct Construction Standards (3rd Edition, 2005), the 2018 or 2021 IMC and IFGC (or Arkansas Fuel Gas Code)
Fees$100 per computer-based exam ($55 paper/pencil), plus Board application and license fees

Sheet metal contractors applying to the Arkansas HVACR Licensing Board for a Class D license, which covers ductwork for HVACR systems without regard to the horsepower of the system the duct connects to. A Class D licensee may not sell, install or service HVACR equipment and systems. Applicants with no license history need 2 years of experience as an HVACR contractor or employee, or Board-approved training.

How to get licensed, step by step

  1. Apply to the Board

    Send the HVACR Licensing Board your Class D application. The Board must pre-approve you before you schedule. Questions: adll.hvac@arkansas.gov or 501-682-9201.

    Arkansas Department of Labor and Licensing: HVACR licensing (opens in a new tab)

  2. Schedule with Prov

    After approval, schedule the computer-based exam with Prov and pay the $100 exam fee. Approval lasts one year.

    Prov (schedule your exam) (opens in a new tab)Prov: Arkansas HVACR candidate bulletin (2025.07.03, archived copy) (opens in a new tab)

  3. Pass the exam

    The exam is open book and timed, with a 70% cut score. Permanent tabs are fine; photocopied books, sticky notes and test-prep guides are not allowed.

    Prov: Arkansas HVACR candidate bulletin (2025.07.03, archived copy) (opens in a new tab)

  4. Get licensed

    Pay the license fee. A Class A, B, D or E licensee is the designated license holder for the company.

    Arkansas Department of Labor and Licensing: HVACR licensing (opens in a new tab)

How to prepare

  • Download the Arkansas HVAC/R Law and Rules (free PDFs from the Department of Labor and Licensing); every HVACR exam has a law and administration section and you may bring printed copies.
  • The 2018 or 2021 IMC and IFGC (or the Arkansas Fuel Gas Code) are allowed. The Board adopted the 2021 International Mechanical Code effective July 1, 2022.
  • Class D covers ductwork only: it does not allow selling, installing or servicing HVACR equipment. Fuel gas systems, install HVAC, layout and fabrication and general knowledge carry the most questions.
  • Learn the SMACNA HVAC Duct Construction Standards for duct construction, and IMC Chapters 5 and 6 for exhaust, chimneys and duct systems.
  • Start with the free questions above to find your weak topics, then drill those first.
  • Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
  • Read every explanation, including for questions you got right, and look the section up in your own book.

Books for this exam

This is an open-book exam: you can bring the references below, and most questions come from the 2021 IMC and the 2018 Arkansas Fuel Gas Code. Tabs and highlighting are allowed. Free online copies are read-only and can't be used in the exam room.

Official reference list (as published by the testing agency)
  • Arkansas HVAC/R Law (free PDF from the Department of Labor and Licensing; candidate-printed copies allowed)
  • Arkansas HVAC/R Rules and Regulations (free PDF from the Department; candidate-printed copies allowed)
  • HVAC Duct Construction Standards, 3rd Edition (2005; SMACNA, ISBN 978-1-61721-030-3)
  • International Mechanical Code (IMC), 2018 or 2021 edition
  • International Fuel Gas Code (IFGC), 2018 or 2021 edition, or the Arkansas Fuel Gas Code 2018 or 2021 edition as a substitute

What's on the exam

Official content outline from Prov (number of questions per topic):

TopicQuestions
Plan Reading, Estimating & Math6
General Knowledge8
Layout & Fabrication8
Install HVAC9
Air Properties & Distribution4
Air Distribution Accessories3
Chimneys, Flues & Exhaust6
Fuel Gas Systems10
Law and Administration6

Exam day details

  • Administered by Prov for the Arkansas HVACR Licensing Board (Department of Labor and Licensing).
  • Fee: $100 for the computer-based exam ($55 paper/pencil) per Prov's bulletin; 17 CAR 261-106(g) also sets $100. Board application and license fees are separate.
  • Prov's bulletin: 60 questions in 3 hours, open book, 70% cut score. Our practice exam uses the same counts and the same nine subject areas.
  • Computer-based exam from Prov (paper/pencil is cheaper). The HVACR Licensing Board must pre-approve you before you schedule; approval lasts one year.
  • All Prov HVACR exams are open book and timed, with a 70% cut score. Books may carry permanent tabs; photocopied books, sticky notes and test-prep study guides are not allowed. The Arkansas HVAC/R Law and Rules may be printed.
  • 17 CAR Part 261 was rewritten after Act 746 of 2025. The copy we studied is an August 2025 draft, so check the final rule.

Note: Format, subject areas and references come from Prov's HVACR bulletin dated July 3, 2025. 17 CAR Part 261 was rewritten after Act 746 of 2025 and our copy is an August 2025 draft, so confirm license limits and any exam changes with the Board and Prov.

Frequently asked questions

What's on the Arkansas HVACR Class D exam?

Nine subject areas: fuel gas systems (10 questions), install HVAC (9), general knowledge (8), layout and fabrication (8), plan reading, estimating and math (6), chimneys, flues and exhaust (6), law and administration (6), air properties and distribution (4) and air distribution accessories (3).

What does a Class D license allow?

Sheet metal work on ductwork for HVACR systems, whatever the size of the system the duct connects to. It does not allow selling, installing or servicing HVACR equipment.

Which books are allowed?

The Arkansas HVAC/R Law and Rules, the SMACNA HVAC Duct Construction Standards (3rd Edition, 2005), the 2018 or 2021 IMC and the 2018 or 2021 IFGC or Arkansas Fuel Gas Code.

Free questions with answers

Show all 10 free questions and answers
  1. A new section of consumer gas piping has a proposed maximum working pressure of 5 psig. Under Section 406.4.1 of the Arkansas Fuel Gas Code, what is the minimum pressure at which it must be tested?

    Answer: 7.5 psig

    Section 406.4.1 requires testing at not less than 1 1/2 times the proposed maximum working pressure, and never less than 3 psig: 5 x 1.5 = 7.5 psig. Testing at 5 psig ignores the multiplier, 10 psig doubles it, and 3 psig is only the floor that applies to low-pressure systems.

    Reference: 2018 Arkansas Fuel Gas Code, Section 406.4.1

  2. Which test medium is NOT permitted for pressure testing new fuel gas piping under Section 406.2 of the Arkansas Fuel Gas Code?

    Answer: Oxygen

    Section 406.2 allows air, nitrogen, carbon dioxide or an inert gas as the test medium and specifically prohibits oxygen, which would create a serious fire and explosion hazard with oils and gas piping.

    Reference: 2018 Arkansas Fuel Gas Code, Section 406.2

  3. A connector from a solid fuel appliance enters a masonry chimney flue. Under Section 801.12 of the 2021 IMC, where must the connector enter the flue?

    Answer: At least 12 inches above the lowest interior portion of the flue

    Section 801.12 requires connectors to enter a chimney flue at a point not less than 12 inches above the lowest portion of the interior of the flue, which leaves room for soot and debris to collect without blocking the connector. Cleanouts are covered separately in Section 801.13.

    Reference: 2021 International Mechanical Code (Arkansas, 17 CAR 261-121), Section 801.12

  4. An exhaust duct under positive pressure carries air from a toilet room. Under Section 601.4 of the 2021 IMC, how may it be routed?

    Answer: It may not extend into or pass through supply or return ducts or plenums

    Section 601.4 says exhaust ducts under positive pressure, chimneys and vents shall not extend into or pass through ducts or plenums, so exhaust air cannot leak into the air being supplied to occupants. Limited exceptions apply, such as sealed exhaust in a ceiling return plenum over spaces with permitted recirculation.

    Reference: 2021 International Mechanical Code (Arkansas, 17 CAR 261-121), Section 601.4

  5. A fire damper is actuated by a fusible link. Under Section 607.3.3.1 of the 2021 IMC, the normal air temperature in the duct is 85 degrees F. What is the minimum operating temperature of the heat-responsive device?

    Answer: 160 degrees F

    Section 607.3.3.1 sets the operating temperature at approximately 50 degrees F above the normal duct temperature but not less than 160 degrees F. Here 85 + 50 = 135 degrees F, which is below the floor, so 160 degrees F governs. A 250 degrees F link is the minimum elevated temperature rating for smoke dampers, not fire damper links.

    Reference: 2021 International Mechanical Code (Arkansas, 17 CAR 261-121), Section 607.3.3.1

  6. A 10-inch round duct carries air at 800 feet per minute. Using Q = A x V, which is the closest airflow?

    Answer: 436 cfm

    Area = pi x r squared = 3.1416 x (5/12 ft) squared = 0.545 square feet, and Q = 0.545 x 800 = 436 cfm. Using the diameter as the radius gives 1,745; using a 10 by 10 inch square gives 556; and forgetting to square the radius gives 1,047.

    Reference: Standard formula (not a code section), Q = A x V (continuity equation)

  7. A duct offsets 18 inches vertically using two 30-degree elbows. Using length = rise divided by the sine of 30 degrees (0.5), what is the length of the angled piece?

    Answer: 36 inches

    Length = rise / sin 30 = 18 / 0.5 = 36 inches. The run is 18 / tan 30 = 31.2 inches (which is not the piece length), and 18 / cos 30 = 20.8 inches uses the wrong function.

    Reference: Standard formula (not a code section), Right-triangle geometry (30-60-90)

  8. Under Chapter 2 of the 2021 IMC, what is transfer air?

    Answer: Air moved from one indoor space to another

    Chapter 2 defines transfer air as air moved from one indoor space to another. Outdoor air enters from outside, and exhaust air is conveyed directly to the atmosphere.

    Reference: 2021 International Mechanical Code (Arkansas, 17 CAR 261-121), Chapter 2, definition of Air, Transfer

  9. A takeoff shows 60 feet of straight rectangular duct that is 18 inches by 10 inches. What is the total sheet metal surface area, ignoring seams and waste?

    Answer: 280 square feet

    Perimeter = 2 x (18 + 10) = 56 inches = 4.667 feet. Area = 4.667 x 60 = 280 square feet. Using half the perimeter gives 140, doubling it gives 560, and multiplying 18 x 10 gives 180.

    Reference: Standard formula (not a code section), Surface area = perimeter x length

  10. Under 17 CAR 261-105(a), when does an Arkansas HVACR license expire?

    Answer: On the last day of the month one year after the original date of issuance

    17 CAR 261-105(a) (2025 draft rule) says licenses expire on the last day of the month one year from the original date of issuance. A license issued March 12, for example, would expire on March 31 of the next year.

    Reference: 17 CAR 261 (HVACR Licensing Board rules, 2025 draft), 17 CAR 261-105(a)

Sources

Questions last verified November 13, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.