Requirements at a glance
| Agency | Georgia Construction Industry Licensing Board (Division of Master and Journeyman Plumbers); exams by PSI |
|---|---|
| Experience | 5 years of plumbing experience, at least 2 of them as a licensed journeyman; at least 2 of the 3 references from licensed master plumbers (Class II) |
| Exam | 140 questions, 7 hours in two 3.5-hour parts, CLOSED book, 70 to pass |
| Books allowed | None: the master plumber exams are closed book. Study the 2024 Georgia Plumbing Code and Gas Code, the NASCLA Georgia guide, Mathematics for Plumbers and Pipefitters and Plumbing Technology |
| Fees | $40 application fee ($30 plus a $10 processing fee) per the Secretary of State form. The PSI exam fee and license fee are not published in the candidate bulletin; confirm them with PSI and the Board. |
Plumbers applying for an unrestricted Georgia master plumber license from the Construction Industry Licensing Board, with 5 years of experience including 2 as a licensed journeyman.
Official links
How to get licensed, step by step
Apply to the Board
Submit the application, three references on the Board's form and the $40 fee to the Construction Industry Licensing Board (Macon; (404) 424-9966). The Board must approve you before you can register with PSI.
Georgia Division of Master and Journeyman Plumbers (CILB) (opens in a new tab)Georgia Rules 121-3 (CILB license requirements) (opens in a new tab)
Register with PSI
After approval, register and pay PSI online or at 855-898-0711. Bring the allowed references and a silent, non-programmable calculator.
Schedule with PSI (Georgia CILB exams) (opens in a new tab)PSI bulletin: Georgia plumbers (opens in a new tab)
Take the exam
Scaled score, 70 to pass. If you fail twice, the PSI bulletin requires a Board-approved review course before a third attempt.
Finish licensing
Send your results and the license fee to the Board.
Georgia Division of Master and Journeyman Plumbers (CILB) (opens in a new tab)
How to prepare
- Georgia's exams are scaled with 70 to pass. The Board's 2026 reference lists apply to exams through December 31, 2026; check for the updated list if you test later.
- Tab your books with permanent tabs before exam day. Highlighting and underlining are allowed; notes, sticky flags and loose papers are not.
- Closed book means you must know the code, not just where to find it: pipe sizing tables, fixture units, vent distances and test pressures.
- 40 questions are business laws (15), administrative requirements (15) and plumbing system design (10).
- Start with the free questions above to find your weak topics, then drill those first.
- Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
- Read every explanation, including for questions you got right, and look the section up in your own book.
What to study
This is a closed-book exam, so nothing comes into the exam room. Study from these:
2024 Georgia Plumbing Code (2024 IPC with Georgia amendments)Essential
The core of the plumbing exams. Open book for journeyman only; master candidates study it for a closed-book exam.
ICC store (opens in a new tab)Read free (UpCodes) (opens in a new tab)
2024 Georgia Gas Code (2024 IFGC with Georgia amendments)Essential
Gas piping, appliance venting and combustion air. On the conditioned air and plumbing lists.
ICC store (opens in a new tab)Read free (UpCodes) (opens in a new tab)
Mathematics for Plumbers and Pipefitters, 8th Edition (Lee Smith)
On the plumbing list. Offsets, grade, volume and pipe-sizing math.
Plumbing Technology, Design and Installation, 4th Edition (Smith and Joyce)
On the plumbing list. Fixtures, installation methods and trade practice.
Contractors Guide to Business, Law, and Project Management: Georgia Construction Industry Licensing Board, 5th Edition (NASCLA)
On the Board's reference lists for the electrical, conditioned air and plumbing exams.
Official reference list (as published by the testing agency)
- 2024 Georgia Plumbing Code (2024 International Plumbing Code with Georgia amendments)
- 2024 Georgia Gas Code (2024 International Fuel Gas Code with Georgia amendments)
- Mathematics for Plumbers and Pipefitters, 8th Edition (Lee Smith)
- Plumbing Technology, Design and Installation, 4th Edition (Smith and Joyce)
- Contractors Guide to Business, Law, and Project Management, Georgia Construction Industry Licensing Board, 5th Edition (NASCLA)
- ADA Standards for Accessible Design (2010), GA 811 Excavator Manual (2025), IRS Employer's Tax Guide and 29 CFR Part 1926 (OSHA)
What's on the exam
Official content outline from PSI Services (number of questions per topic):
| Topic | Questions | |
|---|---|---|
| General Laws | 5 | |
| Regulations | 15 | |
| Work Planning | 7 | |
| Pipe Cutting and Joining | 10 | |
| Installation | 21 | |
| System Testing | 7 | |
| Maintenance and Repair | 15 | |
| Safety | 15 | |
| Calculations | 5 | |
| Business Laws | 15 | |
| Administrative Requirements | 15 | |
| Plumbing System Design | 10 |
Exam day details
- Administered by PSI Services for the Georgia Construction Industry Licensing Board.
- Fee: The Board's initial application fee is $40 ($30 plus a $10 processing fee). The PSI exam fee and the license fee are not published in the candidate bulletin, so check PSI and the Board before you apply.
- 140 scored questions plus 28 unscored pretest questions in 7 hours, split into two 3.5-hour parts.
- Closed book: the Board's reference list is for study only and the master plumber exams do not allow references in the room. Only the journeyman exam is open book.
- Since May 1, 2026 the code questions are based only on the 2024 Georgia Plumbing Code and Gas Code. The master exams add 40 questions on business laws, administrative requirements and plumbing system design.
- The Board must approve your application before you can register with PSI. Scores are scaled and you need 70 to pass.
- The time limit includes the unscored beta (pretest) questions mixed into the exam.
- If you fail twice, the PSI bulletin requires a Board-approved review course before a third attempt.
- Georgia has no statewide journeyman or master electrician exam and no statewide HVAC technician exam; local jurisdictions license those workers.
Frequently asked questions
Is the Georgia master plumber exam open book?
No. The Board's list of references is for study only. The reference materials may not be used on the master plumber exams; only the journeyman exam is open book.
What's on the Georgia Class II master plumber exam?
140 scored questions: 100 technical (regulations 15, installation 21, maintenance and repair 15, safety 15, pipe cutting and joining 10, work planning 7, system testing 7, general laws 5, calculations 5) plus 40 on business laws 15, administrative requirements 15 and plumbing system design 10.
What is the difference between Master Class I and Class II?
Class I is restricted to single-family dwellings, one-level dwellings for not more than two families, and commercial structures up to 10,000 square feet. Class II is unrestricted. They are separate exams with different question counts.
Free questions with answers
Show all 10 free questions and answers
A drainage system is being water tested in sections. What is the minimum head of water that may be applied to any section under test?
Answer: 10 feet
Section 312.2 says sections are not tested with less than a 10-foot head of water, and each successive section overlaps so that no joint except the uppermost 10 feet sees less. The 15-minute hold time is often confused with the head requirement.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 312.2
A 3-inch kitchen waste line runs upstream of a grease interceptor. What minimum slope applies to it?
Answer: 1/4 inch per foot
Section 704.1 overrides Table 704.1 for piping upstream of a grease interceptor: not less than 1/4 inch per foot (2 percent). The 1/8 inch per foot value would otherwise apply to 3-inch pipe.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 704.1
At what static pressure must a pressure-reducing valve be installed on a building water distribution system?
Answer: Where static pressure exceeds 80 psi
Section 604.8 requires an ASSE 1003 or CSA B356 pressure-reducing valve with strainer where static pressure in the building exceeds 80 psi, reducing it to not more than 80 psi static.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 604.8
A plumber is repairing a section of potable water piping. In the absence of a method prescribed by the water purveyor, what is one chlorine disinfection method the code lists?
Answer: At least 50 ppm chlorine solution standing for 24 hours
Section 610.1 gives 50 ppm for 24 hours, or 200 ppm for 3 hours, after flushing until water runs clear. The system must then be flushed until the chlorine is purged and the procedure repeated if bacteriological tests show contamination.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 610.1
What is the maximum horizontal hanger spacing for copper or copper-alloy pipe (not tube) in Table 308.5?
Answer: 12 feet
Table 308.5 lists copper or copper-alloy pipe at 12 ft horizontal and 10 ft vertical. Copper tubing 1-1/4 inch and smaller is 6 ft and 1-1/2 inch and larger is 10 ft.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Table 308.5
A caulked lead joint is made on hub-and-spigot cast-iron soil pipe. What is the minimum depth of the molten lead, and how is it poured?
Answer: At least 1 inch deep, poured in one operation over packed oakum
Section 705.3.1 requires the joint to be packed with oakum or hemp and the lead poured in one operation to not less than 1 inch deep, not receding more than 1/8 inch below the hub rim, then caulked tight. No paint or coating until the joint is tested.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 705.3.1
What is the maximum allowable slope for an excavation in Type B soil when sloping is the protective system, per the OSHA Appendix B simple slope table?
Answer: 1 horizontal to 1 vertical (45 degrees)
Appendix B to Subpart P lists maximum slopes of 3/4:1 for Type A, 1:1 for Type B and 1-1/2:1 for Type C soil. Remember that the more unstable the soil, the flatter the slope.
Reference: 29 CFR Part 1926 (OSHA Construction Standards), 1926 Subpart P, Appendix B, Table B-1
A plumbing contractor pays an employee $1,200 in gross weekly wages. What is the combined Social Security and Medicare tax (employee share plus employer share) on those wages at the standard rates?
Answer: $183.60
Each side pays 6.2% Social Security + 1.45% Medicare = 7.65%. Combined 15.3% x $1,200 = $183.60 ($91.80 withheld from the employee plus $91.80 from the employer). $91.80 is only one share, $74.40 is only the employer Social Security share, and $17.40 is only the employer Medicare share.
Reference: IRS Publication 15 (Employer's Tax Guide), Heading: Social Security and Medicare Taxes
Which insurance covers a plumbing contractor's legal liability when a customer's property is damaged by the crew's work?
Answer: Commercial general liability
Commercial general liability responds to third-party bodily injury and property damage claims arising from operations. Workers' comp covers employees, auto covers vehicles, and builder's risk covers the building project under construction.
Reference: General business practice: insurance, Liability, property damage and auto insurance
The peak drain flow into a gravity grease interceptor serving a restaurant kitchen is 40 gpm. Using the retention time in the Georgia plumbing code, what minimum capacity is required?
Answer: 1,200 gallons
Section 1003.3.7 sets capacity as peak drain flow in gpm multiplied by a 30-minute retention time: 40 gpm x 30 min = 1,200 gallons. Using 60 minutes would give 2,400 gallons, and 15 minutes gives 600.
Reference: 2024 Georgia Plumbing Code (IPC 2024 with Georgia amendments), Section 1003.3.7
Sources
- PSI: Georgia Plumbers Candidate Information Bulletin (Journeyman, Master Class I and II) (opens in a new tab)
- Georgia Division of Master and Journeyman Plumbers (Secretary of State) (opens in a new tab)
- Georgia Rules 121-3 (Construction Industry Licensing Board) (opens in a new tab)
Questions last verified November 14, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.