Illinois licensing exam

Chicago Crane Operator Class II Written Exam: Practice Test & Licensing Guide

Practice for the City of Chicago Class II crane operator written exam (CTS 304), given by CTS: 65 questions in 3 hours on knuckleboom, gantry and floor cranes, operating practices, rigging and signals, inspections, safe working loads and OSHA rules. 70 to pass, closed book.

Questions
65
Time limit
3 hours
Passing score
70%
Books
Closed book
What to study ↓

Full practice test: $19One-time payment · 12 months of access

Try 10 free practice questions

No sign-up. Every answer explains the rule and tells you where to find it in your book.

Question 1 of 10Types of Equipment

An articulating crane with a load hoist was manufactured in 2005. If the machine is covered by Subpart CC, which equipment must it have that prevents hook-block contact with the boom tip?

Requirements at a glance

AgencyCity of Chicago Department of Buildings (Board of Crane Operator Examiners); written exam by Continental Testing Services (CTS), exam code 304
EligibilityAge 21; 2,000 hours operating in the past 48 months or an approved apprenticeship; current federal crane operator certification for the equipment type; other conditions on the City page
Exam65 questions, 3 hours, 70 to pass
ScopeClass II: knuckleboom and articulating cranes, floor and deck cranes, overhead cranes, forklifts with a hook or winch, service and bucket trucks
Book allowedClosed book: no books, notes or references; non-programmable calculator only
Fee$150 written (CTS); practical exam $400 per equipment type; 5-year license $550 (City, 2026)

Operators of Class II equipment in Chicago: articulating and knuckleboom cranes, multi-purpose machines with a hoist, all-terrain forklifts with a hook or winch, floor and deck cranes, overhead cranes, and service or bucket trucks with a hoisting device. The Class II written exam qualifies you for Class II practical exams only.

How to get licensed, step by step

  1. Apply through the City portal

    Applications go through the City's Inspections, Permits and Licenses portal; CTS processes them and runs the written exam.

    City of Chicago: Crane Operator License (opens in a new tab)Continental Testing Services: City of Chicago exams (opens in a new tab)

  2. Pass the written exam

    3 hours, 70 to pass. There are no make-up dates and no refunds; you can re-register for the next date.

    CTS: Chicago Crane Operators study guide (2017) (opens in a new tab)

  3. Study the CTS references

    IPT's Crane and Rigging Training Manual and the OSHA crane and rigging rules, including 29 CFR 1926 Subpart CC.

    CTS: Chicago Crane Operators study guide (2017) (opens in a new tab)OSHA: 29 CFR 1926 Subpart CC, cranes and derricks in construction (opens in a new tab)

  4. Schedule the practical

    A written pass unlocks the practical exam for your equipment type. You must pass at least one practical within one year of the written exam.

    City of Chicago: Crane Operator License (opens in a new tab)

How to prepare

  • CTS's guide is from July 2017, so confirm with CTS that the current exam matches it.
  • Rigging and signals is the largest topic at 17 questions, then safe working loads at 14. Practice sling angle, load weight and capacity-deduction math by hand.
  • There is no personnel hoisting section, but OSHA regulations and workplace safety is 11 questions: power lines, rigging equipment and equipment safety.
  • Start with the free questions above to find your weak topics, then drill those first.
  • Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
  • Read every explanation, including for questions you got right, and look the section up in your own book.

What to study

This is a closed-book exam, so nothing comes into the exam room. Study from these:

Official reference list (as published by the testing agency)
  • Garby, IPT's Crane and Rigging Training Manual (2005)
  • 29 CFR 1910 Subpart N, Sections 176-184 (materials handling and storage)
  • 29 CFR 1926.251 (rigging equipment)
  • 29 CFR 1926 Subpart N, Sections 550-554 (cranes, derricks, hoists)
  • 29 CFR 1926 Subpart O, Sections 600 and 602 (material handling equipment)
  • 29 CFR 1926 Subpart T, Sections 858 and 859 (demolition)
  • 29 CFR 1926 Subpart CC, Sections 1400-1441 (cranes and derricks in construction)

What's on the exam

Official content outline from Continental Testing Services (CTS) (number of questions per topic):

TopicQuestions
Types of Equipment8
Operating Practices9
Rigging & Signals17
Inspections & Maintenance6
Safe Working Loads14
OSHA Regulations & Workplace Safety11

Exam day details

  • Administered by Continental Testing Services (CTS) for the City of Chicago Department of Buildings (Board of Crane Operator Examiners).
  • Fee: $150
  • 65 questions in 3 hours; 70 to pass. The per-topic counts above are the numbers printed in CTS's guide.
  • Closed book: CTS says candidates may not use books, notes or other references. Bring two No. 2 pencils and a non-programmable, non-printing, solar- or battery-powered calculator.
  • Class II has no personnel hoisting section. Rigging and signals (17) is the largest topic, then safe working loads (14).
  • The Chicago license also requires a practical exam per equipment type (CTS 317), the required federal crane operator certification and operating experience. The City lists the 2026 written exam fee as $150 and the practical as $400 per equipment type and exam date.
  • CTS's study guide is dated July 2017. Confirm with CTS that the current exam matches it.

Note: CTS's crane guide is from July 2017 and keyed to OSHA rules of that period; the topic counts, 3-hour limit, 70 pass mark and closed-book rule are from the guide. IPT's manual is not freely readable, so load-chart and rigging math rest on standard formulas and OSHA text.

Frequently asked questions

How many questions are on the Chicago Class II crane operator written exam?

65 questions in 3 hours, with 70 to pass. CTS's guide prints the count for each of the six topics.

Is the Class II exam open book?

No. CTS's guide says candidates may not use books, notes or other reference materials; only a non-programmable calculator is allowed.

Does the Class II exam cover hoisting personnel?

No. CTS's Class II outline has six topics and no personnel hoisting section; that topic (4 questions) appears only on the Class I exam.

Can I operate larger cranes with a Class II pass?

No. Passing the Class II written exam qualifies you only for Class II practical exams. The Class I written exam qualifies you for Class I and Class II practicals.

Free questions with answers

Show all 10 free questions and answers
  1. An articulating crane with a load hoist was manufactured in 2005. If the machine is covered by Subpart CC, which equipment must it have that prevents hook-block contact with the boom tip?

    Answer: A device that automatically prevents damage from two-blocking at every point where it could occur

    Section 1926.1416(d)(3)(iii) requires articulating cranes manufactured after December 31, 1999 with a load hoist to have a device that automatically prevents two-blocking damage at all points where it could occur. Marking the cable and using a spotter is only the temporary alternative while the device is out of order.

    Reference: 29 CFR 1926 Subpart CC, 1926.1416(d)(3)(iii)

  2. Using Table A, what is the minimum clearance distance from equipment, load line and load to an energized 138-kV line?

    Answer: 15 feet

    Table A in 1926.1408 gives 10 ft up to 50 kV, 15 ft over 50 to 200 kV, 20 ft over 200 to 350 kV, and 25 ft over 350 to 500 kV (with a different rule above 350 kV in 1926.1409). A 138-kV line falls in the 'over 50 to 200' row, so 15 feet.

    Reference: 29 CFR 1926 Subpart CC, 1926.1408 Table A

  3. A line is nominally exactly 50 kV and the crew uses the Table A option. What clearance applies?

    Answer: 10 feet, because 'up to 50' includes 50 kV

    In Table A the note states the value after 'to' is included, so up to 50 kV (including 50) requires 10 feet; the 15-foot row starts only above 50 kV. The 6-foot value is from a different table (Table T, traveling with no load).

    Reference: 29 CFR 1926 Subpart CC, 1926.1408 Table A (note)

  4. During a shift inspection of a running (non-rotation-resistant) hoist rope, how many randomly distributed visible broken wires in one rope lay reach the Subpart CC Category II threshold?

    Answer: Six

    Section 1926.1413(a)(2)(ii)(A)(1) sets Category II for running ropes at six randomly distributed broken wires in one rope lay (or three broken wires in one strand in one lay). Two in six diameters and four in 30 diameters are the rotation-resistant rope values, and more than two in one lay (three) is the criterion for pendants or standing ropes beyond the end connections.

    Reference: 29 CFR 1926 Subpart CC, 1926.1413(a)(2)(ii)(A)

  5. A competent person measures a hoist rope and finds its diameter has dropped below nominal. At what reduction does Subpart CC treat this as a Category II apparent deficiency?

    Answer: A reduction of more than 5 percent from nominal diameter

    Section 1926.1413(a)(2)(ii)(B) lists a diameter reduction of more than 5 percent from nominal as a Category II deficiency, which prohibits using the rope until the manufacturer's removal criterion is met, the rope is replaced, or a localized problem is severed out.

    Reference: 29 CFR 1926 Subpart CC, 1926.1413(a)(2)(ii)(B)

  6. Who must begin a visual inspection of a crane before each shift it will be used, and what does that inspection consist of?

    Answer: A competent person, by observing for apparent deficiencies

    Section 1926.1412(d)(1) requires a competent person to begin a visual inspection prior to each shift, to be completed before or during the shift. It is observation for apparent deficiencies; taking components apart or booming down is not required unless the visual check or trial operation shows it is needed.

    Reference: 29 CFR 1926 Subpart CC, 1926.1412(d)(1)

  7. The same 6,000-lb load is now lifted with a two-leg bridle whose legs make only a 30-degree angle with the horizontal. What is the tension in each leg?

    Answer: 6,000 lb

    Tension per leg = 6,000 / (2 x sin 30) = 6,000 / (2 x 0.5) = 6,000 lb, double the vertical-leg share of 3,000 lb. Flattening the legs from 60 to 30 degrees raises each leg from 3,464 to 6,000 lb. 12,000 lb results from multiplying by the legs instead of dividing.

    Reference: Standard rigging formulas (sling angle and load weight); IPT Crane and Rigging Training Manual (2005), concept, Sling angle: tension = load / (legs x sin angle)

  8. A concrete slab is 10 ft long, 6 ft wide and 8 inches thick. Concrete weighs about 150 lb per cubic foot. What is the weight of the slab?

    Answer: 6,000 lb

    Volume = 10 x 6 x (8/12) = 40 cubic feet; weight = 40 x 150 = 6,000 lb. 72,000 lb leaves the thickness in inches (10 x 6 x 8 x 150). 7,500 lb uses 10 inches. 2,496 lb uses the density of water, 62.4 lb per cubic foot.

    Reference: Standard rigging formulas (sling angle and load weight); IPT Crane and Rigging Training Manual (2005), concept, Estimating load weights: volume x density

  9. A crew assumes a power line near the work area is probably deenergized and insulated. What does Subpart CC tell them to presume?

    Answer: That it is energized and uninsulated, unless the owner or an engineer confirms otherwise

    Section 1926.1408(e) requires the employer to assume all power lines are energized unless the utility owner/operator confirms the line has been and continues to be deenergized and visibly grounded at the worksite. The training in (g)(1)(iii) adds that lines are presumed uninsulated unless the owner or a qualified engineer confirms insulation.

    Reference: 29 CFR 1926 Subpart CC, 1926.1408(e) and (g)(1)(iii)

  10. What does Subpart CC require of an employer before an employee operates equipment covered by the standard?

    Answer: That the operator is trained, certified or licensed, and evaluated for that equipment

    Section 1926.1427(a) requires the employer to ensure that each operator is trained, certified/licensed and evaluated before operating covered equipment. An employee not yet qualified may operate only as an operator-in-training under the supervision rules in (b), including continuous on-site monitoring by a trainer.

    Reference: 29 CFR 1926 Subpart CC, 1926.1427(a) and (b)

Sources

Questions last verified November 13, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.