Arizona licensing exam

Arizona CR-42 Roofing Contractor Exam: Practice Test & Licensing Guide

The PSI trade exam for Arizona's CR-42 roofing license: 50 questions on steep- and low-slope roofing, components, estimating, reroofing and fall protection, open book.

Questions
50
Time limit
2 hours
Passing score
70%

Full practice test: $19One-time payment · 12 months of access

Try 10 free practice questions

No sign-up. Every answer explains the rule and tells you where to find it in your book.

Question 1 of 10Estimating and Plan Reading

A gable roof measures 40 ft by 30 ft on the plan view (horizontal projection, overhangs included). The roof slope is 6:12, which has a pitch (slope) factor of 1.118. How many squares of roof surface does the roof have?

Requirements at a glance

AgencyArizona Registrar of Contractors (ROC); trade exam by PSI
Exams50 questions, 120 minutes, 70%, plus the online Statutes and Rules Exam (SRE)
Books allowedIBC and IRC (2009–2018) and 29 CFR 1926
Fees$66 PSI trade exam + $61 SRE, plus ROC license fees and bond

Qualifying parties for an Arizona CR-42 Roofing (residential and commercial) license, or the C-42 and R-42 classifications, which use the same exam.

How to get licensed, step by step

  1. Pick your classification and qualifying party

    Find your classification on the ROC's list. The qualifying party (an owner or regular employee of the business) must have the required trade experience and takes the exams for the business.

    Arizona ROC: License classifications (opens in a new tab)

  2. Pass the Statutes and Rules Exam (SRE)

    Buy the ROC's online SRE course and exam through GMetrix ($61), work through the course, then take the final exam. 70% to pass, one attempt per purchase.

    Buy the Statutes and Rules Exam (GMetrix) (opens in a new tab)

  3. Schedule the CR-42 trade exam with PSI

    Book online with PSI ($66, or $116 for two exams). Bring the allowed references, bound and tabbed. If you fail, wait 30 days to retake.

    Schedule with PSI (Arizona contractors) (opens in a new tab)PSI content outline: CR-42 Roofing (opens in a new tab)

  4. Apply to the ROC

    Submit your application with your passing score reports within two years of passing, plus the license bond, fees and business documents the ROC asks for.

    Arizona ROC: Applying for a license (opens in a new tab)

How to prepare

  • Bring the exact code editions on PSI's list. Arizona's trade exams use older editions (2017 NEC, 2018 I-codes); a newer book gives some wrong answers.
  • Bind or spiral any printed references, and tab them with permanent tabs before exam day. Sticky notes are removed at check-in.
  • Practice finding answers fast. On a 100-question, 4-hour exam you have 2.4 minutes per question, and some of that goes to unscored items.
  • Steep- and low-slope roofing is 20 of 50 questions. Tab IRC Chapter 9 and IBC Chapter 15, especially underlayment, tile and foam roofing.
  • Know fall protection for roofers: 1926.501(b)(10) low-slope rules, warning lines and safety monitors.
  • Start with the free questions above to find your weak topics, then drill those first.
  • Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
  • Read every explanation, including for questions you got right, and look the section up in your own book.

Books for this exam

This is an open-book exam: you can bring the references below, and most questions come from the 2018 IRC and the 2018 IBC. Tabs and highlighting are allowed. Free online copies are read-only and can't be used in the exam room.

Official reference list (as published by the testing agency)
  • International Building Code and International Residential Code, 2009, 2012, 2015 or 2018 (allowed in the exam room)
  • 29 CFR Part 1926, OSHA Construction (allowed in the exam room)
  • Roofing Construction & Estimating, Atcheson (not allowed in the room)
  • The NRCA Roofing Manual: Membrane and Steep-slope Roof Systems (not allowed in the room)

What's on the exam

Official content outline from PSI Services (number of questions per topic):

TopicQuestions
Estimating and Plan Reading5
Surface Preparation and Planning5
Steep and Low Slope Roofing20
Roofing Components10
Safety6
Repairs and Reroofing4

Exam day details

  • Administered by PSI Services for the Arizona Registrar of Contractors (ROC).
  • Fee: $66 to PSI ($116 for two exams taken together). The ROC license application fee is separate.
  • 50 scored questions in 120 minutes, 70% to pass.
  • PSI accepts the 2009 through 2018 IBC and IRC. Our questions use the 2018 editions; where a rule changed between editions, the question says so.
  • Open book: bring your own bound copies of the allowed references. You may highlight and add permanent tabs beforehand, but not write in them during the exam.
  • PSI adds 5 to 10 unscored trial questions, which count against your time.
  • If you fail, wait 30 days to retake; after a third failure the wait is 90 days. Submit your ROC application within two years of passing.
  • You also need Arizona's Statutes and Rules Exam (SRE), taken online through the ROC. The ROC can waive the trade exam if you were the qualifying party on a license in the same classification in the last five years.

Frequently asked questions

What's on the Arizona roofing license exam?

50 questions: steep- and low-slope roofing including built-up roofs and waterproofing 20, roofing components 10, safety 6, estimating and plan reading 5, surface preparation 5 and repairs and reroofing 4.

Does a roofer need a license in Arizona?

Yes. Contracting for roofing work needs an ROC license such as CR-42, R-42 or C-42 (very small jobs may fall under the handyman exemption), with a qualifying party who passes this exam and the Statutes and Rules Exam.

Which code books can I bring to the roofing exam?

The IBC and IRC (2009, 2012, 2015 or 2018 editions) and 29 CFR 1926. The NRCA manuals and Roofing Construction & Estimating aren't allowed in the room.

Free questions with answers

Show all 10 free questions and answers
  1. A gable roof measures 40 ft by 30 ft on the plan view (horizontal projection, overhangs included). The roof slope is 6:12, which has a pitch (slope) factor of 1.118. How many squares of roof surface does the roof have?

    Answer: 13.42 squares

    Plan area = 40 x 30 = 1,200 sq ft. Actual sloped area = plan area x pitch factor = 1,200 x 1.118 = 1,341.6 sq ft. One square is 100 sq ft, so 1,341.6 / 100 = 13.42 squares. 12.00 squares is the flat plan area with no pitch factor, 10.73 comes from dividing by the factor instead of multiplying (1,200 / 1.118 / 100), and 18.00 treats the 6:12 slope as if it added 50 percent.

    Reference: General trade practice (roof estimating), Roof area = plan (horizontal) area x pitch factor; 1 square = 100 sq ft

  2. Under the 2018 IRC, when drip edge and underlayment are installed on a shingle roof, how are they lapped at the eaves and at the rakes?

    Answer: Underlayment goes over the drip edge at eaves and under it at rakes

    IRC R905.2.8.5 says underlayment shall be installed over the drip edge along eaves and under the drip edge along rake edges. IBC 1507.2.8.3 says the same thing. At the eave, water running down the underlayment has to drain onto the drip edge, so the underlayment laps over it. At the rake, the drip edge laps over the underlayment so wind-driven water cannot get under the felt edge.

    Reference: 2018 International Residential Code, Section R905.2.8.5

  3. Under the 2018 IRC, what is the lowest roof slope on which asphalt shingles may be installed?

    Answer: 2 units vertical in 12 units horizontal (2:12)

    IRC R905.2.2 limits asphalt shingles to slopes of 2:12 (17-percent slope) or greater. From 2:12 up to 4:12 the shingles are still allowed, but double underlayment is required per R905.1.1. 4:12 is the point where single-layer underlayment becomes acceptable, not the minimum slope for shingles, and 1:12 is the minimum for mineral-surfaced roll roofing (R905.5.2).

    Reference: 2018 International Residential Code, Section R905.2.2

  4. A concrete tile roof in Tucson (ultimate design wind speed under 140 mph) has a 3:12 slope. How must the underlayment be applied under 2018 IRC Table R905.1.1(2)?

    Answer: Two layers: a 19-inch strip at the eave, then 36-inch sheets lapped 19 inches

    R905.3.2 allows clay and concrete tile down to 2-1/2:12, but from 2-1/2:12 up to 4:12 double underlayment is required. Table R905.1.1(2) describes it: start with a 19-inch strip parallel with the eave, then 36-inch-wide sheets overlapping 19 inches, with 4-inch end laps offset 6 feet. The single layer lapped 2 inches is the method for 4:12 and steeper, and the "all laps 4 inches" rule applies only where V(ult) is 140 mph or more.

    Reference: 2018 International Residential Code, Section R905.3.2 and Table R905.1.1(2)

  5. A concrete tile reroof is planned on a three-story townhouse building whose roof is 46 ft above grade, in an area with an ultimate design wind speed of 140 mph. Under 2018 IRC R905.3.7, how must the attachment of the field tiles be determined?

    Answer: By the tile manufacturer's installation instructions

    2018 IRC R905.3.7 sends clay and concrete tile attachment to the manufacturer's installation instructions where the ultimate design wind speed exceeds 130 mph and the roof is more than 40 feet above grade. This building meets both conditions (140 mph, 46 ft), so Table R905.3.7 is not used. The two-fasteners-per-tile rule is for areas subject to snow, "every other row" is a Table R905.3.7 value, and perimeter tiles always need at least one fastener each.

    Reference: 2018 International Residential Code, Section R905.3.7

  6. A chimney measures 36 inches wide perpendicular to the slope of the roof. What does the IRC require on its upslope (ridge) side?

    Answer: A cricket or saddle

    IRC R903.2.2 (IBC 1503.5) requires a cricket or saddle on the ridge side of any chimney or penetration more than 30 inches wide measured perpendicular to the slope. At 36 inches this chimney needs one. The cricket covering must be sheet metal or the same material as the roof covering. Step flashing is still used at the sides, but it does not replace the cricket.

    Reference: 2018 International Residential Code, Section R903.2.2

  7. Metal valley flashing is being formed for a concrete tile roof. Under IRC R905.3.8, how far must it extend from the valley centerline, and what splash diverter rib is required?

    Answer: 11 inches each way, with a rib at least 1 inch high

    R905.3.8 (IBC 1507.3.9) requires tile valley flashing of at least 0.019-inch (No. 26 galvanized) corrosion-resistant metal extending not less than 11 inches from the centerline each way, with a splash diverter rib not less than 1 inch high at the flow line and 4-inch end laps. The 8-inch, 3/4-inch-rib values are for metal roof shingle valleys (R905.4.6), and 10 inches is the wood shingle value on slopes under 12:12.

    Reference: 2018 International Residential Code, Section R905.3.8

  8. A vented attic over a house in Mesa has a ceiling area of 1,800 sq ft. Using the basic 1/150 ratio in IRC R806.2, what is the minimum total net free ventilating area in square inches?

    Answer: 1,728 sq in

    R806.2 requires a net free ventilating area of at least 1/150 of the vented space: 1,800 / 150 = 12 sq ft. Converting, 12 x 144 = 1,728 sq in. 864 sq in uses the 1/300 exception ratio without meeting its conditions, 1,200 sq in multiplies square feet by 100 instead of 144, and 3,456 sq in wrongly applies the full ratio separately to both intake and exhaust.

    Reference: 2018 International Residential Code, Section R806.2

  9. A crew is installing a modified bitumen roof on a 2:12 roof that is 40 ft wide and 22 ft above grade. When does 29 CFR 1926.501(b)(10) allow a safety monitoring system alone, without a warning line?

    Answer: When the roof is 50 feet or less in width

    1926.501(b)(10) allows low-slope roofing work to be protected by guardrails, nets, PFAS, or a warning line combined with one of those or with a safety monitoring system. On roofs 50 ft or less in width, a safety monitoring system alone is permitted. This 40-ft-wide, 2:12 (low-slope) roof qualifies. The height of the edge does not create the exception; width does.

    Reference: 29 CFR 1926 (OSHA Construction Standards), 29 CFR 1926.501(b)(10)

  10. A Scottsdale homeowner wants new concrete tile installed over the existing clay tile roof to save tear-off cost. What does the 2018 IRC say?

    Answer: Not permitted; a recover over clay or concrete tile is prohibited

    R908.3.1.1 (IBC 1511.3.1.1) lists conditions where a recover is not permitted, including where the existing roof covering is slate, clay, cement or asbestos-cement tile. The tile must come off. R908.5 does allow the existing undamaged clay or cement tile to be reinstalled after the tear-off, but cracked or broken tile may not be reused.

    Reference: 2018 International Residential Code, Section R908.3.1.1

Sources

Questions last verified October 20, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.