Alabama licensing exam

Alabama Journeyman Plumber Exam: Practice Test & Licensing Guide

The Prov exam for the Alabama journeyman plumber license: 75 open-book questions on the 2021 IPC and IFGC, trade math, sizing, fixtures, drainage, water heaters and Alabama plumbing and gas law. 70% to pass.

Questions
75
Time limit
2.9166666666666665 hours
Passing score
70%
Books
Open book

Full practice test: $19One-time payment · 12 months of access

Try 10 free practice questions

No sign-up. Every answer explains the rule and tells you where to find it in your book.

Question 1 of 10Drain Waste and Vents

What is the minimum slope for a horizontal 4-inch building drain that is not upstream of a grease interceptor?

Requirements at a glance

AgencyAlabama Plumbers and Gas Fitters Examining Board (PGFB); exam by Prov
Exam75 questions, 175 minutes, 70% to pass, open book
Books allowed2021 IPC and IFGC, Mathematics for Plumbers and Pipefitters (8th), Modern Plumbing (8th), Admin. Code ch. 720 and Ala. Code Title 34 Ch. 37
Fee$110 to the Board; Board license fees are separate

Plumbers applying for an Alabama journeyman plumber license from the Plumbers and Gas Fitters Examining Board.

How to get licensed, step by step

  1. Meet the eligibility requirement

    The Board's application asks for 2 years of current work as an apprentice plumber.

    Alabama Plumbers and Gas Fitters Examining Board (opens in a new tab)

  2. Apply to the board

    Send the Board your application and fee. After you pass, send the Board your pass certificate within 90 days.

    Alabama Plumbers and Gas Fitters Examining Board (opens in a new tab)

  3. Schedule with Prov

    Exam fees are handled through the Board, not paid to Prov. Prov grades the exam right away and sends your result to the board. If you fail, wait 30 days before retesting.

    Schedule with Prov (opens in a new tab)

  4. Bring your references

    All of these exams are open book. Bring the exact books the bulletin lists; permanent tabs and pen highlighting are allowed, sticky notes and loose notes are not.

    Prov bookstore (reference books) (opens in a new tab)

How to prepare

  • General knowledge (10) and sizing and design (9) are the largest sections. Tab the IPC fixture-unit and pipe-sizing tables.
  • Handwritten formulas are allowed in your reference books, so add the formulas you use for trade math before exam day.
  • Alabama plumbing and gas law (5) comes from Ala. Code Title 34 Chapter 37 and Admin. Code chapter 720.
  • Start with the free questions above to find your weak topics, then drill those first.
  • Take at least two full timed simulations before exam day. Timing is where most people fail open-book exams.
  • Read every explanation, including for questions you got right, and look the section up in your own book.

Books for this exam

This is an open-book exam: you can bring the references below. Tabs and highlighting are allowed. Free online copies are read-only and can't be used in the exam room.

    Official reference list (as published by the testing agency)
    • International Plumbing Code (IPC), 2021 edition (allowed in the exam room)
    • International Fuel Gas Code (IFGC), 2021 edition (allowed in the exam room)
    • Mathematics for Plumbers and Pipefitters, 8th Edition (allowed in the exam room)
    • Modern Plumbing, 8th Edition, Goodheart-Willcox (allowed in the exam room)
    • Alabama Administrative Code Chapter 720 (2018) and Code of Alabama 2022, Title 34, Chapter 37, Plumbers and Gas Fitters (allowed in the exam room)

    What's on the exam

    Official content outline from Prov, Inc. (number of questions per topic):

    TopicQuestions
    General Knowledge10
    Drawings and Plan Reading5
    Trade Math6
    Tools5
    Sizing and Design9
    Fixtures and Fittings6
    Drain Waste and Vents6
    Roof Drain Systems5
    System Installation7
    Water Heaters6
    Safety5
    Alabama Plumbing and Gas Law5

    Exam day details

    • Administered by Prov, Inc. for the Alabama Plumbers and Gas Fitters Examining Board.
    • Fee: $110 to the Plumbers and Gas Fitters Examining Board with your application. Board license fees are separate.
    • 75 questions in 175 minutes; 70% to pass.
    • Eligibility per the Board's application: 2 years of current work as an apprentice plumber.
    • Prov (provexam.com, (801) 733-4455) gives the exam for the Alabama Plumbers and Gas Fitters Examining Board (PGFB). Exam fees are handled through the Board, not paid to Prov.
    • A new Board approval is required before each attempt, and you wait 30 days to retest.
    • Open book. Hand-written formulas are allowed in the reference books on this exam (the bulletin notes this for the listed books); sticky notes are not allowed.

    Frequently asked questions

    What's on the Alabama journeyman plumber exam?

    75 questions: general knowledge 10, sizing and design 9, system installation 7, trade math 6, fixtures and fittings 6, drain waste and vents 6, water heaters 6, drawings and plan reading 5, tools 5, roof drain systems 5, safety 5 and Alabama plumbing and gas law 5.

    Which code editions does it use?

    The 2021 International Plumbing Code and 2021 International Fuel Gas Code, which Alabama's plumbing exams have used since 2023.

    Is it open book?

    Yes. Bring the references listed by the Board, such as the IPC, IFGC, Modern Plumbing and Mathematics for Plumbers and Pipefitters.

    Free questions with answers

    Show all 10 free questions and answers
    1. What is the minimum slope for a horizontal 4-inch building drain that is not upstream of a grease interceptor?

      Answer: 1/8 inch per foot

      Table 704.1 lists 1/8 inch per foot for horizontal drainage pipe 3 to 6 inches. The 1/4 inch per foot value applies to pipe 2-1/2 inches or smaller, and to any piping upstream of a grease interceptor.

      Reference: 2021 International Plumbing Code, Table 704.1

    2. A plumber wants to tie a mechanical room floor drain into the building storm drain to save pipe. What does the code say?

      Answer: Floor drains must not be connected to a storm drain

      Section 1104.2 states plainly that floor drains shall not be connected to a storm drain. Floor drains receive sanitary or process waste and belong on the sanitary system or an approved indirect path.

      Reference: 2021 International Plumbing Code, Section 1104.2

    3. Two water closets in a public restroom are installed side by side with no partition between them. What is the minimum center-to-center spacing the code allows?

      Answer: 30 inches

      Section 405.3.1 requires 30 inches center to center between adjacent fixtures when partitions or obstructions do not separate them. Fifteen inches is the center-to-wall dimension, not the fixture-to-fixture dimension.

      Reference: 2021 International Plumbing Code, Section 405.3.1

    4. Where must the temperature relief element of a storage water heater's relief valve sense water, and what may be installed between the valve and the tank?

      Answer: In the top 6 inches of the tank, with no shutoff or check valve allowed

      Section 504.4.1 requires temperature relief valves to be located so they are actuated by water in the top 6 inches of the tank, and there shall be no check valve or shutoff valve between the relief valve and the heater.

      Reference: 2021 International Plumbing Code, Section 504.4.1

    5. What is the smallest nominal diameter permitted for a water service pipe to a structure?

      Answer: 3/4 inch

      Section 603.1 says the water service pipe must be sized to supply the required quantities and pressures, and shall not be less than 3/4 inch in diameter.

      Reference: 2021 International Plumbing Code, Section 603.1

    6. What is the maximum horizontal hanger spacing for PVC drainage pipe under Table 308.5?

      Answer: 4 feet

      Table 308.5 lists 4 feet horizontal and 10 feet vertical for PVC pipe. Six feet is the horizontal spacing for small copper tubing, and 10 feet is for large copper tubing.

      Reference: 2021 International Plumbing Code, Table 308.5

    7. What is the maximum vertical distance from a fixture outlet to the trap weir?

      Answer: 24 inches

      Section 1002.1 limits the vertical distance from the fixture outlet to the trap weir to 24 inches and the horizontal distance to 30 inches measured from the centerline of the fixture outlet to the centerline of the trap inlet.

      Reference: 2021 International Plumbing Code, Section 1002.1

    8. What does the code mean by 'lead free' solder and flux for joining water supply piping?

      Answer: A chemical composition equal to or less than 0.2 percent lead

      Section 605.12.3 defines lead free as equal to or less than 0.2 percent lead. The 8 percent figure is the limit for pipe and fittings under Section 605.2, and 0.25 percent is the weighted-average limit for drinking-water fixtures under Section 605.2.1.

      Reference: 2021 International Plumbing Code, Section 605.12.3

    9. A cylindrical hot water storage tank is 24 inches in diameter and 48 inches tall. Using 7.48 gallons per cubic foot, about how many gallons does it hold?

      Answer: 94 gallons

      Radius = 1 ft and height = 4 ft. Volume = pi x 1 squared x 4 = 12.57 cubic feet. Gallons = 12.57 x 7.48 = 94 gallons. Using the 24-inch diameter as the radius would quadruple the answer to about 376 gallons.

      Reference: Plumbing trade mathematics (standard formula), Volume of a cylinder x 7.48 gal per cubic foot

    10. A drawing shows the invert of a 4-inch building drain at elevation 100.00 feet where it leaves the building. The drain runs 60 feet to a cleanout at the minimum slope in Table 704.1. To the nearest hundredth of a foot, what is the invert elevation at the cleanout?

      Answer: 99.38 feet

      Table 704.1 requires 1/8 inch per foot for 3- to 6-inch pipe. Fall = 60 ft x 1/8 in/ft = 7.5 inches = 0.625 foot. Invert = 100.00 - 0.625 = 99.375, or 99.38 feet. Using 1/4 inch per foot gives 98.75, and forgetting to convert inches to feet gives 92.50.

      Reference: 2021 International Plumbing Code, Table 704.1

    Sources

    Questions last verified November 17, 2026. Licensing rules change. Always confirm current requirements with the licensing agency before you apply.